Monday, February 01, 2010

PVC Greenhouse: Sizing your greenhouse


When I get around to scanning my hand drawn plans for my greenhouse you will see that I intended a 6 foot wide, 10 foot long 8 foot high frame with ribs made of 10 foot pipe lengths. This planning was well intentioned but the resulting greenhouse was a monster. I know because I loosely assembled it and was awed by its size. I adjusted mid-course in a few areas and now have a more modest 5 x 10* x 6 high with 8 foot ribs. Let me provide some sizing guidance and tell you about my experience working with PVC.

*10 feet actually became 11 feet which I explain below.



Watch your greenhouse "grow"
Whatever the initial dimensions of your pipe lengths are cut to, expect them to grow a little as you assemble them. The reason is that each tim you cut a pipe to insert a fitting you are adding between 1 and 2 inches.

In my case, I started with 10 ft long 1 inch PVC for the long base pipes. I need to cut those 10 foots to insert the T--shape pipe fitting where the ribs attached at the base. Each of the six T-pipe fitting is 2 1/2 inches long. No matter how hard you try to shove the ends of the cut pipe into the pipe fitting you'll have difficulty getting them inserted flush. In addition, there is at least 3/4 inch of space in the middle of the T to accommodate the rib attachment. So, in my case, my long 10- foot base pipe was almost 11 feet long.


Square Structure Sizing
I used 1 inch PVC for the square structure. When shopping for your PVC pipe grab two different 10 foot long piece: 1-3/4 inch and 1-1 inch. You'll notice the 3/4 inch bends and drops and the 1 inch basically holds its form. It was the rigidity of the 1 inch that drove me in that direction for the square structure. If you are going to have any dimension in your structure greater than 10 feet, I'd recommend upgrading above the 1 inch. This will add weight and dollars to your project so you may want to keep it to 10 ft. or less.

Additionally, consider whether you want to hang baskets from square frame. If so, you can upgrade the PVC pipe above 1 inch, add vertical supports half way down the 10 foot pipe, or plan to run galvanized electrical metal tubing inside your PVC for greater stability.

Curvature and length of the ribs
I used 3/4 inch PVC for the ribs. This seemed just flexible enough to bend around the square 1 inch pipe frame while still solid enough for a reliable structure. The 1 inch pipe is firm enough to hold mostly square and not to bow while 3/4 inch pipe is bent around it. However, where the ribs meet the square structure is a stress point . You need the ribs to be about 2 feet longer than the height of the square structure. If they are less the square structure will bow and curve under the ribs.

Ribs spacing
Space your ribs at about 2 feet apart. This should give the proper amount of support when it is time to add the exterior sheeting. If you cut lengths of pipe at 2 ft and add T fittings the spacing will be a bit over 2 ft but, in the end, it will be fine.

PVC is not an exact science
I'd like to close the sizing section with the notion that PVC was not made for this kind of contruction. When you start to fit you pipes and fitting together variances will be introduced. One pipe inserts 3/4 of inch into the fitting but anoth 5/8 of an inch. A T fitting for a one inch pipe adds 2 inches of length but a T fittings for a 3/4 inch pipe add less. In the end the dimensions change and grow as you assemble no matter how well you plan. The good news is that PVC is flexible...You should be too!!!


Tags: , ,

9 comments:

bobby said...

Hi, is it possible to modify your house to be 20 ish x 20ish 6-8 foot high house?
Thanks
Bobby

lisaray said...

I have made my greenhouse. It's 4X6. I also plants many things inside this greenhouse.

Reese Delorey said...

This is a great design. I love PVC greenhouses. I've been playing around with integrating my watering system into the framing to avoid dragging the hose around. That shape that you made rocks, though.

Unknown said...

Help? My PVC hoop type greenhouse of 10 x 15 has collapsed in only 25mph winds. Apparently, bending the 3/4 inch PVC pipes to fit into the 4way connectors along the roof have proved to much pressure. 2-3 of them have broken, allowing the pipes to break through the 6 mil greenhouse plastic. How to best fix this? Would installing 45* connectors to the 4ways with a 2" piece of PVC help with the pressure? I'm just glad it wasn't filled with starts yet.

Positibo Pananaw said...

great idea about pvc pipes

Master Pipe said...

Really nice blog, Thanks for sharing.
Plumbing Pipe

Unknown said...

Great guide. A good distributor of the pipe clamps used in projects is Fastfix Southeast Asia.

Hex Hanger said...

Cutting-Edge Design Transforms The Familiar Hex Hanger Into Today's Sanitary Standards. These stainless pipe hangers are utilized with hygienic equipment in the bio-tech, pharmaceutical, food, beverage and dairy industries. Our hex pipe hangers are essential to PVF installations, supporting BPE style stainless steel and copper tubing, schedule pipe, PVC coated pipe, conduits and instrumentation lines

Online Tips said...

Great post I would like to thank you for the efforts you have made in writing this interesting and knowledgeable article.
http://www.valvefittingstore.com/pipe-fittings-2